More options
| % of 1RM | Load | Approx. reps to failure | Training use |
|---|
| Reps | Predicted max load | % of 1RM |
|---|
The weight you should be able to lift for each number of reps to failure, based on your estimated 1RM and the selected formula.
Loads for a given number of reps at each RPE (Rate of Perceived Exertion). RPE 10 = no reps left, RPE 8 = 2 reps left. Based on the widely used RPE/RIR percentage chart.
| Set | Load | Reps | Rest after |
|---|
A conservative 1RM test built from your estimate. Stop at any attempt that slows down badly or loses technique – the last clean single is your 1RM. Always use a spotter or safety bars.
Each formula was fitted to a different group of lifters, so they disagree, especially above 10 reps. The spread shows how uncertain any single estimate is.
Sets of five are the backbone of strength training, from 5×5 programmes to classic barbell routines. This 5 rep max calculator turns your best set of five into an estimated one rep max, and it also works backwards: switch to I know my 1RM to find the weight you should manage for five. It’s pre-set to 5 reps and opens on the Rep maxes tab. The general one rep max calculator handles any other rep count.
Why a 5RM is a great way to estimate your max
- Accurate: Reynolds, Gordon and Robergs (2006) found 1RM predictions from a 5RM were more accurate than predictions from 10RM or 20RM sets.
- Safe: at about 86% of your max, you’re heavy enough for a good estimate without the strain of a true single.
- The formulas agree: at 5 reps the seven equations only differ by about 6% (for 100 kg: 112.5–119 kg). At 15 reps they differ by about 25%.
- Easy to test often: you can hit a top set of five in a normal session, so you can track progress every few weeks.
5RM to 1RM conversion table
| 5RM (kg) | Est. 1RM (kg) | 5RM (lb) | Est. 1RM (lb) |
|---|---|---|---|
| 40 | 46.2 | 95 | 110 |
| 50 | 57.7 | 115 | 133 |
| 60 | 69.3 | 135 | 156 |
| 70 | 80.8 | 155 | 179 |
| 80 | 92.4 | 175 | 202 |
| 90 | 103.9 | 195 | 225 |
| 100 | 115.4 | 215 | 248 |
| 110 | 127.0 | 235 | 271 |
| 120 | 138.5 | 255 | 294 |
| 130 | 150.1 | 275 | 317 |
| 140 | 161.6 | 295 | 341 |
| 150 | 173.2 | 315 | 364 |
| 160 | 184.7 | 335 | 387 |
| 180 | 207.8 | 355 | 410 |
| 200 | 230.9 | 395 | 456 |
What percentage of your max is a 5RM?
It depends on the formula and on you. The equations put a 5RM between 84% (Mayhew) and 88.9% (Brzycki and O’Conner) of 1RM, with Epley at 85.7%. The average of 86.6% is a solid default. In practice:
- Strength-focused lifters often have a 5RM nearer 88–90% of their max, so the calculator may slightly under-estimate them.
- Endurance-focused or high-rep trainees often have a 5RM nearer 82–85%, so the calculator may slightly over-estimate them.
How to test your 5 rep max
- Warm up: empty bar × 10, then about 40%, 55% and 70% of your target for 5, 3 and 2 reps.
- Do one set of 5 at your best guess. If it was RPE 8 or easier, rest 3–4 minutes, add 2.5–5%, and go again.
- Stop when a set of five reaches RPE 9–10. That’s your 5RM for the day. Enter it above with the matching RPE.
Prefer heavier sets? The 3 rep max calculator converts triples instead. For any rep count from 1 to 30, see the full rep max chart.
Using your 5RM in a programme
Many beginner and intermediate routines (5×5 and 3×5 styles) start working sets a little below your current 5RM, then add weight every session. A sensible start for 5 sets of 5 is about 85–90% of your 5RM, which is roughly 75–78% of your 1RM. Increase by 2.5 kg (upper body: 1–1.25 kg) per session while you complete every rep with good form.
5RM FAQs
How do I calculate my 1RM from my 5RM?
Multiply your 5RM by about 1.15 (seven-formula average 1.154). By Epley, it’s × 1.167; by Brzycki, × 1.125. 120 kg × 5 → about 138.5 kg.
How do I calculate my 5RM from my 1RM?
Multiply your 1RM by about 0.866. A 150 kg max suggests a 5RM of about 130 kg. Switch the calculator to I know my 1RM and open the Rep maxes tab.
What percentage is 5 reps of max?
Roughly 85–89% of your 1RM depending on the formula, about 86.6% on average.
Reference: Reynolds JM, Gordon TJ, Robergs RA (2006), J Strength Cond Res 20(3):584–592. For training guidance only.