Deadlift Max Calculator (Deadlift 1RM Calculator)

Quick answer: enter your deadlift weight and reps to estimate your max deadlift. Example: 140 kg × 5 reps ≈ 162 kg deadlift 1RM, and 315 lb × 5 ≈ 364 lb. Formulas tend to under-estimate the deadlift, so treat the result as a floor, not a ceiling.
More options

Estimated one rep max
–kg
–Training max (90%)
–× bodyweight
–Est. 5-rep max
% of 1RMLoadApprox. reps to failureTraining use
RepsPredicted max load% of 1RM

The weight you should be able to lift for each number of reps to failure, based on your estimated 1RM and the selected formula.

Loads for a given number of reps at each RPE (Rate of Perceived Exertion). RPE 10 = no reps left, RPE 8 = 2 reps left. Based on the widely used RPE/RIR percentage chart.

SetLoadRepsRest after

A conservative 1RM test built from your estimate. Stop at any attempt that slows down badly or loses technique – the last clean single is your 1RM. Always use a spotter or safety bars.

Each formula was fitted to a different group of lifters, so they disagree, especially above 10 reps. The spread shows how uncertain any single estimate is.

This deadlift max calculator estimates your one rep max for the conventional, sumo or trap bar deadlift from a set of 1–20 reps. Because the deadlift behaves differently from the squat and bench, this page explains how to get a realistic number and how to use it, alongside your training percentages, warm-up attempts and plate loading. For any other exercise, use the main 1RM calculator.

Why deadlift estimates are different

When LeSuer et al. (1997) checked seven popular 1RM equations against tested maxes, the formulas worked well for the bench press and squat but tended to under-predict the deadlift. There are good reasons for this:

  • Grip and back fatigue end sets early. In a set of 8, your grip or lower back may give out long before your legs and hips do, so you do fewer reps than your strength suggests.
  • Each rep starts from a dead stop. There’s no stretch-shortening “bounce” to help, which makes reps 2+ relatively harder than on other lifts.
  • Heavy singles are a skill. Experienced pullers often move much more for one rep than their rep work predicts.

What to do: use sets of 1–5 reps (doubles and triples are ideal), reset fully between reps, and treat your estimate as a conservative floor. Many strong lifters find their true max sits near the top of the range the calculator shows.

Deadlift 1RM from reps

Reps to failureAt 100 kgAt 140 kgAt 180 kgAt 315 lb
1100140180315
2106.0148.4190.8334
3109.2152.9196.6344
4112.4157.3202.3354
5115.4161.6207.8364
6118.5165.9213.3373
8124.7174.5224.4393
10130.9183.3235.6412
Estimated deadlift 1RM. Seven-formula average; real deadlift maxes often land a little higher.

Conventional, sumo and trap bar

Estimate each style separately, because the maxes don’t transfer one-to-one. Most lifters pull more with whichever of conventional or sumo suits their build, and many lift more on a trap (hex) bar because the load sits in line with the body and the handles are often higher. Keep a separate number for each and don’t programme one from the other’s max.

Deadlift percentages and programming

The deadlift is very demanding to recover from, so most programmes use fewer, heavier sets and lower total volume than for the squat. Many lifters deadlift heavy just once a week:

SessionSets × reps% of 1RMExample (1RM 180 kg)
Heavy3 × 2–385–90%152.5–162.5 kg
Moderate4 × 475–80%135–145 kg
Speed / technique6–8 × 165–70%117.5–125 kg

Use the Plate loader tab to set up the bar quickly. On a 20 kg bar, 180 kg is a 25, 25, 20 and 10 kg plate on each side. If you train by feel, our RPE calculator converts an RPE 8 double into deadlift loads.

How your deadlift compares

The deadlift is usually the heaviest of the three powerlifts. Common ratios: your squat max is often 80–90% of your deadlift, and pulling 2× bodyweight is a widely used intermediate milestone. These are rules of thumb only. To compare your total with lifters of other bodyweights, use our strength calculator.

Testing your deadlift max safely

  • Brace before the bar leaves the floor and keep it close to your legs. If your back rounds noticeably, the attempt is over.
  • Use chalk and, for testing, a mixed or hook grip so your grip doesn’t cap your max. Straps are fine for training but not for a competition-style max.
  • Don’t grind a pull for more than a few seconds. Lower it under control and finish the session.
  • The full warm-up and attempt plan is in our one rep max test guide.

Deadlift max FAQs

Why does my deadlift estimate feel too low?

Rep-based formulas commonly under-estimate the deadlift because grip and lower-back fatigue end multi-rep sets early. Re-estimate from a heavy double or triple, or treat the top of the range as your likely max.

Should I use touch-and-go reps for the calculator?

Use dead-stop reps if you can: let the plates settle on the floor and reset each rep. Touch-and-go reps borrow momentum and make the estimate less comparable to a true single.

If I deadlift 140 kg for 5, what’s my max?

About 162 kg by the seven-formula average, with a range of about 157.5–166.5 kg. Your real max may be a little higher.

Reference: LeSuer DA et al. (1997), J Strength Cond Res 11(4):211–213. For training guidance only.