Bench Press Max Calculator (Bench 1RM Calculator)

Quick answer: to calculate your max bench, enter a recent hard set below. Example: 80 kg × 5 reps ≈ 92.5 kg bench 1RM, and 185 lb × 5 ≈ 214 lb. Count only reps where the bar touches your chest and you lock out fully.
More options

Estimated one rep max
–kg
–Training max (90%)
–× bodyweight
–Est. 5-rep max
% of 1RMLoadApprox. reps to failureTraining use
RepsPredicted max load% of 1RM

The weight you should be able to lift for each number of reps to failure, based on your estimated 1RM and the selected formula.

Loads for a given number of reps at each RPE (Rate of Perceived Exertion). RPE 10 = no reps left, RPE 8 = 2 reps left. Based on the widely used RPE/RIR percentage chart.

SetLoadRepsRest after

A conservative 1RM test built from your estimate. Stop at any attempt that slows down badly or loses technique – the last clean single is your 1RM. Always use a spotter or safety bars.

Each formula was fitted to a different group of lifters, so they disagree, especially above 10 reps. The spread shows how uncertain any single estimate is.

“What is my max bench?” is probably the most-asked question in any gym. This bench press one rep max calculator answers it without the risk of getting pinned. Enter any set of 1–20 reps and you’ll get your estimated bench max, a likely range, bench press percentages for your training, and a warm-up that builds safely to a new PR. For other lifts, use the general one rep max calculator.

How to calculate your max bench

  1. After warming up, bench a weight you can lift for 3–6 reps, ideally with a spotter.
  2. Count reps with a full touch on the chest and full lockout. Don’t count bounced reps.
  3. Enter the weight and reps, and set the RPE if you stopped short of failure.
  4. Read your estimate and range, then open the % of 1RM tab for your working weights.

By hand, the quickest method is Epley: max bench = weight × (1 + reps ÷ 30). 80 kg × 5 gives 80 × 1.167 = 93.3 kg. Our guide to 1RM formulas shows how the other six equations compare.

Bench press 1RM from reps

Reps to failureAt 60 kgAt 80 kgAt 100 kgAt 225 lb
16080100225
263.684.8106.0239
365.587.4109.2246
467.489.9112.4253
569.392.4115.4260
671.194.8118.5267
874.899.7124.7281
1078.5104.7130.9295
Estimated bench 1RM (kg columns in kg, last column in lb). Seven-formula average.

How accurate are bench press max estimates?

The bench press is the lift that rep-max equations predict best, because it’s mostly limited by muscle strength and not by balance or grip. In LeSuer et al. (1997), the Mayhew and Wathen equations came closest to tested bench maxes. Brzycki was originally designed with sets of up to 10 reps in mind (Brzycki, 1993). Keep your test set under about 10 reps and the estimate is usually within a few kilos.

Paused vs touch-and-go: pausing the bar on your chest, as powerlifting rules require, removes the stretch reflex, so paused maxes are typically a few percent lower. Estimate from the style you want to know your max in.

Bench press percentages for training

GoalSets × reps% of bench 1RMExample (1RM 100 kg)
Strength5 × 385–88%85–87.5 kg
Strength–size4 × 677–80%77.5–80 kg
Muscle growth3 × 1067–72%67.5–72.5 kg
Paused technique3 × 470–75%70–75 kg

Bench progress is slower than squat or deadlift progress because smaller muscles are involved. Adding 1–1.25 kg a week (micro-plates) keeps you progressing much longer than jumping 2.5 kg. Set Round loads to 1.25 kg in the calculator’s options to get matching percentages.

What’s a good bench press?

It depends heavily on bodyweight, sex and training age, so compare yourself as a multiple of bodyweight. A bodyweight bench (1×) is a common first big goal for men, and 0.6–0.75× bodyweight for women. 1.25–1.5× is a strong lifter in either group. These are rules of thumb, not official standards. For a fair comparison across bodyweights, enter your squat, bench and deadlift into our strength calculator to get your DOTS score. Your bench is also worth comparing with your overhead press max: most lifters press around 60–70% of their bench.

Testing your bench max safely

  • Always use a spotter or a rack with safety arms set just above chest height. Never bench heavy with collars on when you’re alone; if you get stuck you need to be able to tip the plates off.
  • Agree a lift-off and a “take it” signal with your spotter before the attempt.
  • Use a full grip with your thumbs wrapped around the bar. A thumbless “suicide” grip has caused serious accidents.
  • Use the Warm-up & 1RM test tab for loads, and see our one rep max test guide for the full protocol.

Bench max FAQs

If I bench 100 kg for 5 reps, what’s my max?

About 115 kg, with the formulas ranging from 112.5 to 119 kg.

Can I estimate my bench max from dumbbells?

Not reliably. Dumbbells need more stabilisation, so your dumbbell numbers don’t convert cleanly to a barbell max. You can still use the calculator to find your dumbbell bench 1RM per hand and track that.

Why is my estimated bench higher than what I can actually lift?

Usually because the test set included bounced or partial reps, or because you have good muscular endurance. Re-estimate with a heavier, strict set of 2–4 reps for a tighter number.

References: LeSuer DA et al. (1997), J Strength Cond Res 11(4):211–213; Brzycki M. (1993), JOPERD 64(1):88–90. For training guidance only.