Overhead Press 1RM Calculator (OHP Max Calculator)

Quick answer: enter your overhead press weight and reps. Example: 50 kg × 5 reps ≈ 57.5 kg OHP 1RM, and 115 lb × 5 ≈ 133 lb. For the press, sets of 3–6 strict reps give the most reliable estimate.
More options

Estimated one rep max
–kg
–Training max (90%)
–× bodyweight
–Est. 5-rep max
% of 1RMLoadApprox. reps to failureTraining use
RepsPredicted max load% of 1RM

The weight you should be able to lift for each number of reps to failure, based on your estimated 1RM and the selected formula.

Loads for a given number of reps at each RPE (Rate of Perceived Exertion). RPE 10 = no reps left, RPE 8 = 2 reps left. Based on the widely used RPE/RIR percentage chart.

SetLoadRepsRest after

A conservative 1RM test built from your estimate. Stop at any attempt that slows down badly or loses technique – the last clean single is your 1RM. Always use a spotter or safety bars.

Each formula was fitted to a different group of lifters, so they disagree, especially above 10 reps. The spread shows how uncertain any single estimate is.

This OHP calculator estimates your one rep max for the standing barbell overhead press (also called the military press or shoulder press) from any set. It works for the push press and seated press too, as long as you keep each style separate. You’ll get press percentages, rep maxes and micro-loading options, because the overhead press is the lift where small jumps matter most. Other lifts are covered by our main 1RM calculator.

Overhead press 1RM from reps

Reps to failureAt 40 kgAt 50 kgAt 60 kgAt 135 lb
1405060135
242.453.063.6143
343.754.665.5147
445.056.267.4152
546.257.769.3156
647.459.371.1160
849.962.374.8168

Getting an accurate press estimate

  • Strict means strict. No knee dip and no excessive back lean. Once your legs help, it’s a push press, which typically allows noticeably more weight.
  • Keep sets short. The shoulders and triceps fatigue quickly, and form breaks down on long sets. Sets of 3–6 give the best estimates.
  • Lockout counts. A rep only counts if the bar finishes over the middle of your foot with your elbows locked.

OHP to bench press ratio

A useful check on upper-body balance: most lifters strict press around 60–70% of their bench press max. If your press is well below 60% of your bench, extra overhead work and upper-back training often help both lifts and your shoulder health.

Bench 1RMTypical OHP (60–70%)
60 kg36–42 kg
80 kg48–56 kg
100 kg60–70 kg
140 kg84–98 kg
225 lb135–158 lb

Programming the overhead press

Because the numbers are small, a standard 2.5 kg jump can be 5% of your max, too much to progress by week after week. In the calculator’s options, set Round loads to 1 kg or 0.5 kg if your gym has fractional plates. A simple progression:

  • Weeks 1–3: 4 × 6 at 72.5–77.5%, adding 1 kg per week.
  • Weeks 4–6: 5 × 3 at 82.5–87.5%.
  • Week 7: re-estimate from a top set of 3–5, or test a new max with our 1RM test protocol.

OHP FAQs

Can I use dumbbell press numbers?

You can estimate your dumbbell shoulder press 1RM per dumbbell, but it won’t convert neatly to a barbell max. Track each separately.

Seated or standing, which should I use?

Either, as long as you’re consistent. Seated pressing removes the need to brace your whole body and often allows a little more weight.

Estimates are for training purposes only and aren’t medical advice.