RPE Calculator (RPE to 1RM and RPE Chart)

Quick answer: RPE 10 means no reps left, RPE 9 means 1 rep left, RPE 8 means 2 left, and so on. Enter a set and its RPE below to get your e1RM. Then use the RPE chart tab for loads at any reps and RPE. Example: 100 kg × 5 @ RPE 8 ≈ 121–124 kg e1RM.
More options

Estimated one rep max
–kg
–Training max (90%)
–× bodyweight
–Est. 5-rep max
% of 1RMLoadApprox. reps to failureTraining use
RepsPredicted max load% of 1RM

The weight you should be able to lift for each number of reps to failure, based on your estimated 1RM and the selected formula.

Loads for a given number of reps at each RPE (Rate of Perceived Exertion). RPE 10 = no reps left, RPE 8 = 2 reps left. Based on the widely used RPE/RIR percentage chart.

SetLoadRepsRest after

A conservative 1RM test built from your estimate. Stop at any attempt that slows down badly or loses technique – the last clean single is your 1RM. Always use a spotter or safety bars.

Each formula was fitted to a different group of lifters, so they disagree, especially above 10 reps. The spread shows how uncertain any single estimate is.

RPE (Rate of Perceived Exertion) lets you train by how hard a set feels instead of by a fixed percentage, so your loads match how strong you are today. This RPE calculator does two jobs. It estimates your one rep max from any set you’ve rated by RPE, and it gives you the load to use for any target such as “3 reps @ 8”. Choose the RPE in the calculator, then open the RPE chart tab. If you only have sets taken to failure, the standard 1RM calculator works just as well.

The RPE scale for lifting

The modern lifting RPE scale is tied to reps in reserve (RIR): how many more good reps you could have done. It was popularised by powerlifting coach Mike Tuchscherer and validated by Zourdos et al. (2016), who found that experienced lifters rate RPE accurately, especially on heavier sets.

RPEReps in reserveWhat it feels like
100Maximal. No more reps possible, and no more weight.
9.50–1Couldn’t do another rep, but could have added a little weight.
91Definitely one more rep in the tank.
8.51–2One more for sure, maybe two.
82Two more reps possible. Heavy but controlled.
7.52–3Two or three left.
73Fast, confident reps. A typical “speed” or technique set.
6 and below4+Warm-up territory.

RPE percentage chart

This is the widely used RPE chart, showing the percentage of 1RM for each combination of reps and RPE. Multiply by your 1RM to get your working weight, or let the calculator above do it, rounded to your plates.

Reps@10@9.5@9@8.5@8@7.5@7@6.5
1100%97.8%95.5%93.9%92.2%90.7%89.2%87.8%
295.5%93.9%92.2%90.7%89.2%87.8%86.3%85.0%
392.2%90.7%89.2%87.8%86.3%85.0%83.7%82.4%
489.2%87.8%86.3%85.0%83.7%82.4%81.1%79.9%
586.3%85.0%83.7%82.4%81.1%79.9%78.6%77.4%
683.7%82.4%81.1%79.9%78.6%77.4%76.2%75.1%
781.1%79.9%78.6%77.4%76.2%75.1%73.9%72.3%
878.6%77.4%76.2%75.1%73.9%72.3%70.7%69.4%
976.2%75.1%73.9%72.3%70.7%69.4%68.0%66.7%
1073.9%72.3%70.7%69.4%68.0%66.7%65.3%64.0%
1170.7%69.4%68.0%66.7%65.3%64.0%62.6%61.3%
1268.0%66.7%65.3%64.0%62.6%61.3%59.9%58.6%
Each half-point of RPE shifts the load by about one column. “5 @ 8” uses the same percentage as “7 @ 10”, because both leave you 7 reps from failure.

How to calculate e1RM from RPE

There are two equivalent ways, and the calculator shows both:

  1. Chart method: divide the weight by the chart percentage. 100 kg × 5 @ 8 → 100 ÷ 0.811 = 123.3 kg.
  2. Reps-in-reserve method: add the reps in reserve to the reps done, then use a rep-max formula. 5 reps + 2 RIR = 7 reps to failure → 100 kg × 7 → about 121.6 kg by the seven-formula average. This is the number shown in the result box.

The two methods usually land within 1–2%. For a deeper look at the formulas behind the second method, see how to calculate 1RM.

Training with RPE: a practical example

Your programme says “bench 3 × 5 @ RPE 8”. Your e1RM is 100 kg, and the chart says 5 @ 8 = 81.1%, so you load 80 kg for the first set. If it feels like RPE 7, add 2.5 kg for the next set. If it feels like RPE 9, drop 2.5 kg. Over weeks your e1RM climbs and the loads rise with it, without ever needing to test a max. This is called autoregulation, and it’s why RPE has become so popular with powerlifters and coaches.

Tips for rating RPE accurately

  • Rate straight after the set, before the feeling fades.
  • Use bar speed as a clue: if the last rep slowed noticeably, you’re probably at RPE 9 or above.
  • Beginners tend to under-rate. They think they had 2 left when they had 4–5. Use RPE alongside percentages until you’ve tested where failure really is a few times.
  • Accuracy improves with heavier sets (Zourdos et al., 2016). Ratings on sets of 1–5 are more reliable than on sets of 12+.

RPE FAQs

What is RPE 8 in percentage terms?

It depends on the reps: a single at RPE 8 is about 92% of 1RM, a set of 5 about 81%, and a set of 8 about 74%. See the chart above.

What’s the difference between RPE and RIR?

They’re two sides of the same scale. RIR is reps in reserve, and RPE = 10 − RIR. So 2 RIR is RPE 8.

Is RPE better than percentages?

Neither is strictly better. Percentages give structure, and RPE adjusts for daily readiness. Many programmes combine them, for example “top set of 3 @ RPE 8, then 3 × 5 at 85% of that weight”.

References: Zourdos MC et al. (2016), J Strength Cond Res 30(1):267–275; Helms ER et al. (2016), Strength Cond J 38(4):42–49. For training guidance only.