One Rep Max Test: How to Test Your 1RM Safely

Quick answer: a 1 rep max test is a series of warm-up sets that get heavier while the reps drop (about 40% → 85% of your expected max), followed by 2–3 single attempts with 3–5 minutes’ rest. Aim to finish within 3–5 heavy singles. Enter a recent set below and the Warm-up & 1RM test tab gives you every load.
More options

Estimated one rep max
–kg
–Training max (90%)
–× bodyweight
–Est. 5-rep max
% of 1RMLoadApprox. reps to failureTraining use
RepsPredicted max load% of 1RM

The weight you should be able to lift for each number of reps to failure, based on your estimated 1RM and the selected formula.

Loads for a given number of reps at each RPE (Rate of Perceived Exertion). RPE 10 = no reps left, RPE 8 = 2 reps left. Based on the widely used RPE/RIR percentage chart.

SetLoadRepsRest after

A conservative 1RM test built from your estimate. Stop at any attempt that slows down badly or loses technique – the last clean single is your 1RM. Always use a spotter or safety bars.

Each formula was fitted to a different group of lifters, so they disagree, especially above 10 reps. The spread shows how uncertain any single estimate is.

Estimating your max from reps is safe and accurate enough for most people. But sometimes you want the real number: before a powerlifting meet, at the end of a training block, or simply to know where you stand. This page gives you a step-by-step one rep max test based on the National Strength and Conditioning Association (NSCA) protocol, and the calculator above builds the exact loads for you from a recent set. Don’t have a recent hard set? Estimate one first with the 1RM calculator.

Before you test: are you ready?

  • Technique: you should have trained the lift consistently for several months and be able to keep good form on sets at 85–90%.
  • Health: no current injuries, and no medical conditions that make maximal straining unsafe (for example uncontrolled high blood pressure). If in doubt, ask a doctor or physiotherapist.
  • Recovery: test after 2–4 lighter days, well slept and fed. Don’t test at the end of a hard week.
  • Safety set-up: a spotter who knows what they’re doing, or a rack with safety bars set correctly.

Beginners, older lifters and anyone returning from injury usually get everything they need from an estimated max. A heavy set of 3–5 put into the calculator is a safer alternative. See our 3RM to 1RM converter.

The one rep max test protocol

Based on the NSCA’s 1RM testing guidelines (Haff & Triplett, 2016), adapted with typical percentages:

  1. General warm-up (5–10 min): light cardio and mobility for the joints involved.
  2. Light set: 8–10 reps at about 40% of your expected max (or the empty bar). Rest 1 minute.
  3. Build: 5 reps at about 50%, then 3 at 65%, resting 1–2 minutes between sets.
  4. Near-max primers: 2 reps at about 75%, then a single at about 85%. Rest 2–3 minutes.
  5. Opener: a single at about 90–92%. This should feel heavy but confident. Rest 3–5 minutes.
  6. Second attempt: about 95–97%. If it moved well, rest 3–5 minutes.
  7. Third attempt: your estimated max or a small PR (100–103%).
  8. If you miss: rest 3–5 minutes and either retry with 2.5–5% less, or call it a day. The NSCA recommends finding the 1RM within about 3–5 heavy attempts, because more attempts mean fatigue starts to work against you.

Example test: expected max of 140 kg

SetLoadRepsRest after
Warm-up 155 kg (40%)8–101 min
Warm-up 270 kg (50%)51–2 min
Warm-up 390 kg (65%)32 min
Warm-up 4105 kg (75%)22–3 min
Warm-up 5120 kg (85%)13 min
Opener130 kg (92%)13–5 min
Attempt 2135 kg (97%)13–5 min
Attempt 3142.5 kg (102%)1Done

Choosing your attempts

  • Opener: a weight you could do for 2–3 reps on a bad day. Its job is to build confidence.
  • Use bar speed: if the opener flew up, jump 5% or more. If it was slow, make a small jump (2–3%).
  • Small jumps near the top: on the bench and overhead press, use 1–2.5 kg jumps. On the squat and deadlift, use 2.5–5 kg.
  • Stop on form, not on failure. A rep that rounds your back, caves your knees or needs a spotter to finish isn’t a valid max.

Lift-specific safety

  • Squat: safety bars set just below your depth, or two side spotters. Practise bailing with light weight.
  • Bench press: always use a spotter or safeties. Wrap your thumbs around the bar, and never bench a max alone with collars on.
  • Deadlift: no spotter needed, but stop if your back rounds. Chalk up and use a hook or mixed grip.
  • Overhead press: press inside a rack with safeties at shoulder height if you can.

After the test

Write down the weight, the date, your bodyweight and the equipment you used (belt, sleeves, wraps). Switch the calculator to I know my 1RM and enter your new max to get your training percentages, or print the full 1RM chart. Take a few lighter days afterwards. Max testing is very tiring, especially for the nervous system. Most lifters don’t need to test more than every 8–16 weeks, and can track progress in between by estimating from top sets, ideally rated with the RPE scale.

1RM test FAQs

How long should I rest between 1RM attempts?

3–5 minutes between heavy singles. The NSCA protocol suggests 2–4 minutes; most lifters do better at the longer end on the squat and deadlift.

How often should I test my one rep max?

Every 8–16 weeks at most, usually at the end of a training block. Estimate from training sets in between.

Should beginners do a 1RM test?

Generally no. Beginners get stronger so quickly that a max is out of date within weeks, and technique often breaks down on maximal attempts. Estimating from a set of 5 is safer and just as useful.

Reference: Haff GG, Triplett NT (eds) (2016), Essentials of Strength Training and Conditioning, 4th edn, NSCA / Human Kinetics. Maximal lifting carries risk. Lift within your ability and with appropriate supervision. This page isn’t medical advice.